Yamaha Music Mixer DM2000 V2 User Manual

Cubase SX3 / DM2000 V2 Setup and Operation  
Page 1  
Cubase SX3 / DM2000 V2 Setup and Operation  
This document describes setup and operation for remote control of Cubase SX from the  
DM2000 digital mixing console. These instructions apply to DM2000 V2.0 or higher  
and Cubase SX V3.0.0 or higher.  
Driver Installation  
1)  
Connect your PC or Macintosh computer  
The DM2000 should be connected to your computer by connecting the TO HOST  
USB port on the DM2000 to a USB port on your computer.  
2)  
Install Driver  
Once your computer is connected, you will need to install the USB-MIDI driver  
included on the DM2000 CD-ROM. It is recommended that you install the latest  
driver which can be downloaded from www.yamahaproaudio.com  
Configuring DM2000 V2  
1)  
2)  
Press the [SETUP] display access key and select the MIDI/TO HOST screen.  
Set the DAW port assignment to USB 2-5 (this allows USB port 1 to be used for  
the DM2000 Studio Manager Editor software). Note: you must use USB ports 2-  
5 for DAW Control and USB port 1 for Studio Manager if you intend to use these  
two applications simultaneously.  
3)  
4)  
5)  
Press the [REMOTE] display access key and assign CUBASE SX as the Target  
for one of the Remote layers.  
(See “About Remote Layers” in the DM2000 manual for more information.)  
Press the [LOCATOR] display access key and select DAW Control as the  
function for the transport and locate keys. This allows the Cubase SX transport to  
be controlled regardless of whether a Remote or Internal mixing layer is active.  
Press the relevant [REMOTE] LAYER button to select the Cubase SX Remote  
Control Layer.  
When the Cubase SX Remote Control Layer is selected, the DM2000’s control  
surface controls Cubase SX rather than the internal mixing of the DM2000. In  
order to control the DM2000, you need to select an Input Channel Layer or the  
Master Layer. Audio mixing on the Input and Master Layers, and Automix  
continues while the Cubase SX Layer is selected.  
 
Cubase SX3 / DM2000 V2 Setup and Operation  
Page 3  
level shown in the fluorescent display section. In this mode, each send can be switched  
On/Off by pressing the encoder.  
Selected Channel Functions  
Pressing any of the DISPLAY switches in the SELECTED CHANNEL section of  
DM2000 will cause the VST Audio Channel Settings window to open in Cubase SX.  
COPY & PASTE  
The CHANNEL COPY and PASTE switches on DM2000 perform the same functions as  
COPY and PASTE in Cubase SX’s Edit menu.  
EQ  
The four bands of EQ GAIN, FREQUENCY and Q on DM2000 control the same  
functions on the selected Cubase SX channel, and the parameter value is displayed on the  
console. To switch an EQ band On or Off, hold down the FREQUENCY/Q encoder for  
one second.  
The entire EQ section can be bypassed by pressing the EQ ON key in the SELECTED  
CHANNEL section of DM2000. (Note: when the EQ ON LED is lit in the DM2000, this  
indicates EQ Bypass in Cubase SX.)  
PANNING  
The PAN encoder and the JOYSTICK on DM2000 control the pan functions of Cubase  
SX. Even if there is no surround panning enabled, the joystick can be used for Left-Right  
panning.  
AUX SENDS  
The AUX SEND LEVEL encoders and ON switches edit the 8 sends in Cubase SX. So  
only the first two BANKS on DM2000 are used. By pressing the LEVEL encoders, the  
send can be switched between Pre and Post Fader.  
PHASE AND INSERT  
The PHASE switch on DM2000 switches the phase of the selected Cubase SX channel,  
and the INSERT ON switch bypasses all Inserts for the selected channel.  
 
Cubase SX3 / DM2000 V2 Setup and Operation  
Page 4  
FX Sends, Routing and Insert Editing  
FX SENDS  
In the EFFECTS / PLUG-INS section of the DM2000, press the INTERNAL EFFECTS  
key to access FX Send information on the LCD screen. The encoders below the screen  
can edit various functions:  
Encoder 1 edits the send level.  
Encoder 2 edits the send On/Off status (by turning the encoder).  
Encoder 3 edits between Pre and Post Fader (by turning the encoder).  
Pressing any of the encoders will switch all sends On/Off.  
There are 8 sends spread over 8 pages. To access different sends, use the UP and DOWN  
cursor buttons to the left of the LCD encoders.  
ROUTING  
Press the PLUG-INS switch to access Routing information in the LCD. There are two  
pages, accessed by pressing the UP and DOWN cursor buttons to the left of the LCD  
encoders. The following functions can be edited:  
Page 1  
Encoder 1 chooses the Output Bus for the selected channel  
Encoder 2 switches the Monitor On/Off (by pressing or turning the encoder)  
Encoder 3 selects the Input bus  
Encoder 4 edits the Input Gain (the encoder must be pressed down while turning)  
Page 2  
Only Encoder 1 has a function. It is used to switch the Input Phase On/Off (by pressing  
or turning the encoder).  
INSERTS  
When the CHANNEL INSERTS switch is pressed on DM2000, the LCD shows Insert  
information for the selected channel.  
Encoder 1 selects which insert is to be edited  
Encoder 2 switches the insert On/Off (by turning, not pressing)  
Encoder 3 selects the type of effect to insert  
Once an Effect has been selected, all the parameters can be edited by changing the page  
viewed on the LCD (by pressing the UP and DOWN cursor buttons to the left of the LCD  
encoders). The number of pages available depends on the number of parameters used by  
the Effect.  
Note: in any of the above modes, the EFFECT DISPLAY switch toggles between  
showing the parameter names and the parameter values on the LCD.  
 
Cubase SX3 / DM2000 V2 Setup and Operation  
Transport & Automation  
Page 5  
Ensure that DAW CONTROL is selected in the LOCATE MEMORY screen of the  
LOCATOR display menu on DM2000.  
TRANSPORT CONTROLS  
The following Transport functions can be controlled from DM2000:  
REC  
PLAY  
STOP  
FF  
REW  
SCRUB  
SHUTTLE  
LOOP  
QUICK PUNCH  
ONLINE  
LOCATE FUNCTIONS  
The following DM2000 locate functions also control the corresponding Cubase SX  
functions:  
RTZ  
END  
IN  
OUT  
SET  
LOCATE 1-8  
To set a locate point (Marker in Cubase SX), hold the SET switch on DM2000, and press  
the required LOCATE MEMORY switch at the required time. Note: DM2000 must be in  
the appropriate Cubase SX Remote Layer in order to set Markers.  
TRACK-ARMING  
The DM2000 TRACK ARMING 1-24 switches control the RECORD ENABLE switches  
of the corresponding Cubase SX channels.  
AUTOMATION  
The following AUTOMIX switches on DM2000 control automation functions of Cubase  
SX:  
ENABLE puts all Cubase SX channels into READ mode  
REC puts all Cubase SX channels into WRITE mode.  
The AUTO switch above each DM2000 channel fader switches READ On/Off for  
each channel individually. However, when AUTO-REC is switched on, the channel  
AUTO switches function to control WRITE On/Off in Cubase SX.  
 
Cubase SX3 / DM2000 V2 Setup and Operation  
User Defined Keys  
Page 6  
When DM2000 is used to remotely control Cubase SX, the following User Defined Keys  
have permanently assigned functions:  
UDEF 1: Brings the Project window to the front  
UDEF 2: Scrolls channels down in banks of 8  
UDEF 3: Scrolls channels up in banks of 8  
UDEF 9: Open or closes the VST Mixer window  
UDEF 10: Scrolls channels down one channel at a time  
UDEF 11: Scrolls channels up one channel at a time  
Other User Defined Keys (UDEF 4-8 and 12-16) can be programmed by the user to  
control various Cubase SX functions. These functions can be selected in the DEVICE  
SETUP of Cubase SX, by selecting “YAMAHA DM2000 V2” and choosing the desired  
‘Category’ and ‘Command’ from the drop-down list for each button.  
Other Functions  
ZOOM & NAVIGATION  
The DM2000 CURSOR keys (next to the Scrub Wheel) have two different functions.  
Their mode can be changed by pressing the INC key above the cursor keys. The mode is  
shown on the LCD display.  
ZOOM mode: the cursor keys control the vertical and horizontal zoom of the Project  
Window.  
NAVIGATION mode: the cursor keys control the selection of channels and objects in  
the Project Window.  
TIME COUNTER  
The TIME COUNTER is displayed on the DM2000 LCD screen, with the counter mode  
(TIME CODE / FEET / BEATS). If “Samples” is selected in Cubase SX, then no  
selection is displayed in the DM2000 LCD.  
METER BRIDGE  
The DM2000 meter bridge displays Cubase SX’s input channel levels when the correct  
REMOTE layer is selected. The TIME CODE counter is also displayed on the Meter  
Bridge.  
 

Weil McLain Water Heater GL E223 ADOC 0311 User Manual
Whirlpool Cooktop 8285116 User Manual
Whirlpool Ice Maker EHC511 User Manual
Wolf Indoor Furnishings STAND C 48 User Manual
Xerox All in One Printer 4500 PS TR User Manual
Xilinx Computer Hardware UG133 User Manual
Zanussi Electric Heater ZBX 623 SS User Manual
Zanussi Ice Maker 730164 User Manual
Zanussi Oven ZDF867 User Manual
Zephyr Ventilation Hood ZVE E30AS User Manual